Skip to content
English
  • There are no suggestions because the search field is empty.

Restrict Where Timeclock Can Be Used by IP Addresses

Stämplingsterminaler · Steg-för-steg-guide
Uppdaterad 2026-11-20 16:03
Short answer

With the Timeclock module you can specify which IP addresses are allowed to use Timeclock's protected functions. Open the terminal under Administration → Terminals, fill in Allowed IP addresses and then test from both an allowed and another network. An empty field means no IP restriction.

The IP restriction is suitable when Timeclock is to be used from one or several specific workplaces with stable outgoing IP addresses. It complements terminal assignment and identification but does not replace your usual permissions or network protection.

[!NOTE] The function is included in the Timeclock module There is no verified separate add-on for IP restriction alone. If you lack the Timeclock module or cannot find the pages for terminals, you can contact Timeplan to review needs and activation. Price, terms and schedule will be confirmed in that dialogue.

Fördjupning
Before you begin

Seek assistance from the person responsible for the network. You need to know the outgoing IP address that Timeplan sees when the terminal connects. This is often a public address from the workplace's internet connection, not the local address shown on the computer or tablet.

For the restriction to be stable, the addresses usually need to be fixed or otherwise predictable. If the internet provider, a VPN service, a proxy or other network equipment changes the address Timeplan sees, the terminal may be denied access until the list is updated.

Prepare the following before saving:

  • the name of the Timeclock terminal to be restricted
  • the IP addresses confirmed by your IT administrator
  • a way to test from an allowed network
  • another network to verify that the restriction actually applies

Important: Do not enter a guessed local address. Verify the address that Timeplan sees and plan the test while an authorised administrator can revise the setting. Clearing the field will completely remove the IP restriction.

Steg för steg
Restrict the terminal
Open the correct terminalGo to Administration → Terminals, open the terminal used for the web-based Timeclock page and check the terminal name before making any changes. #### Further information - Check the terminal name and description so you do not change the wrong workplace. The IP list applies to the opened terminal, not all terminals in the installation. - This guide applies to the web-based Timeclock page. Ask Timeplan and your IT administrators to verify the model before using the IP list as an operational lock for older physical terminal equipment. - The fields Active and Reading allowed should not be used as substitutes for IP restriction. They have not been verified as general shutdown buttons for a terminal already accessible.
Enter allowed addressesType the confirmed addresses in Allowed IP addresses, select Save and then read back the list. > [!WARNING] > Read back the list after saving > > The current product may remove some invalid characters before the address is validated. A typing error therefore does not always produce the error message you expect. Check the saved address character by character. #### Further information - Enter an address without spaces. If several addresses should be allowed, separate them with semicolons, for example 203.0.113.10;203.0.113.11. Do not use duplicates. The entire field can contain up to 300 characters. - An empty field means that Timeclock does not restrict access based on IP address. Do not clear the field as a troubleshooting step without first considering whether the broader access is acceptable. - Timeclock compares the address the service actually sees with the saved list. A VPN service, proxy or change by the internet provider may therefore cause a previously allowed workplace to be denied until the list is updated. - An address that does not match is denied when Timeclock uses protected functions such as identification, clocking, balance retrieval, self-registration and transmission of offline clockings.
Steg för steg
Test and verify the result
Test from an allowed networkOpen Timeclock from the workplace’s intended network and use an authorised test employee according to your usual routine. #### Further information - Check a protected function as part of your test routine, for example that identification can retrieve the necessary data. Simply viewing the terminal’s start page is not sufficient for verification. - The page itself and the login step may open before the IP restriction is enforced. A visible page does not prove that identification or clocking is permitted. - The test must use the correct terminal, a valid employment contract and an allowed identification method. The IP list does not replace these conditions.
Test the restriction from another networkOpen the same Timeclock address from a connection whose IP address is not in the list and verify that a protected function is denied. Interrupt if the test requires an actual clocking that should not be saved. #### Further information - Timeclock should deny the protected function and show that the terminal is not allowed to be used from that location. That the start page is still visible is not a failed test. - Check together with the IT administrator which outgoing address the other network uses. The test is not valid if the connection happens to go through the same allowed VPN, proxy or internet gateway as the workplace. - The test should not create incorrect working time or use another employee’s identity. If a real registration is required instead, follow your usual controlled testing routine. - If the unauthorised network can still use a protected function, read back the list, check the visible remote address and contact Timeplan before considering the restriction operational.
Verify the resultConfirm that the intended workplace works, that the other network is denied and that the saved list matches the IT documentation. #### Further information - Document which outgoing addresses are allowed and who is responsible for updating the list when the internet connection, VPN or proxy changes. - If an allowed workplace is locked out, an authorised administrator can correct the list. An empty field removes the IP restriction completely and should only be used when the broader access is intentional. - IP restriction complements terminal assignment, identification rules and your other network protection. It does not replace these controls.
Fördjupning
What the restriction affects

A filled address list is checked when Timeclock uses its protected terminal functions. An address that does not match cannot use, among other things, identification, clocking, balance retrieval, self-registration or transmission of offline clockings.

The restriction does not necessarily hide the web address and is not the same as employee terminal assignment. A person still needs the correct terminal, a valid employment contract and an allowed identification method.

This guide applies to the web-based Timeclock page. Do not assume that every older physical terminal model uses the same network control.

Fördjupning
Relations to other parts of Timeplan
Steg för steg
Frequently Asked Questions
Do we need a fixed IP address?For a reliable restriction, the address that Timeplan sees needs to be stable. A fixed outgoing IP address is therefore normally the simplest solution. Ask your internet or network provider to confirm what applies for the workplace.
Can we allow multiple workplaces?Yes. Enter each allowed IP address in the same field and separate the addresses with semicolons.
Why can the start page be opened from a network that is not allowed?IP checking is performed when Timeclock uses the protected terminal functions. Seeing the start page does not mean that identification or clocking is permitted.
What happens if the field is empty?No restriction is made based on IP address. Do not clear the field as a troubleshooting step without first considering whether the broader access is acceptable.
Is IP restriction a separate add-on module?No, not according to the current product material. The function is included in the Timeclock module. Contact Timeplan if you wish to verify whether the module is part of your solution or to discuss activation.